The paper band around a skein is worth keeping: it helps you identify the yarn and find its care instructions later.
A yarn label commonly lists fiber content, weight and length, a suggested gauge and needle size, care instructions, and color or batch identifiers. The layout and available information vary by brand and market. The compositions and color names below are illustrative examples, not a particular manufacturer’s label.
Yarn weight symbol
The skein-shaped icon with a number inside is the Craft Yarn Council’s yarn thickness category. Its published chart runs from 0 (Lace) to 7 (Jumbo). That number is not a needle size, a weight in grams, or a count of the strands plied together.
You may also see names such as DK, Worsted, or Bulky. Not every brand uses the CYC system. Check the category, length, fiber content, and gauge together; a product name alone does not identify thickness.
The yarn weight chart breaks down all the categories with their gauge ranges and typical needle sizes.
Fiber content
Listed as percentages. 100% Merino Wool. 75% Acrylic, 25% Wool. 60% Cotton, 40% Modal. This is the “made from” section, and it affects everything about how the finished fabric will feel, drape, stretch, and wear over time.
Pay attention here when substituting yarn. A wool DK and a cotton DK may sit in the same weight range, but the fabric won’t behave the same way at all. The fiber comparison guide covers those differences.
Labels sometimes note whether the yarn is superwash, mercerized, or brushed. Superwash describes a treatment that helps wool resist felting; follow the specific yarn’s washing instructions. The word alone gives no permission to tumble dry, iron, or steam block.
Gauge information
A knitting gauge box gives stitches across and rows vertically over the stated area, often 10 × 10 cm or 4 × 4 inches, with a suggested knitting needle size. A crochet gauge or hook recommendation is separate: don’t read a hook size as a knitting needle size. Check whether sizes are in millimeters or a regional numbering system, and read any stated stitch pattern or treatment conditions.
The label gauge is a reference, not a guarantee of your gauge or finished fit. Make a swatch in your pattern’s stitch pattern, treat it as allowed for that yarn, and measure it dry against the pattern’s gauge. If the label does not state whether its gauge is measured before or after washing, don’t assume.
Put-up information
Skein weight in grams and yarn length in yards, meters, or both. Two numbers, but the length is the one that matters for project planning. Two 100 g skeins can contain very different lengths because thickness, fiber, and construction differ. Equal weight or length does not make them interchangeable. This is why the yarn estimation guide works from yardage, not skein count.
Care symbols
The descriptions here refer to the GINETEX / ISO care-symbol system. Other systems and older labels differ; use the manufacturer’s explanation if a mark is unfamiliar. These are descriptions in words, not reproductions of standardized pictograms. GINETEX’s symbol guide shows the actual shapes.
Washing: the washtub’s number is a maximum temperature in °C, not a temperature you must use. One bar underneath means a mild process; two mean very mild. Neither means hand wash. A hand in the tub means hand washing; check the indicated variant and temperature. A crossed-out tub prohibits domestic washing, including hand washing.
Bleaching: an empty triangle allows chlorine or oxygen bleach; two diagonal lines allow oxygen bleach only. A crossed-out triangle means no bleach.
Drying: a circle inside a square refers to tumble drying. One dot means low heat, two normal heat; a cross over this symbol prohibits tumble drying. A square with one horizontal line means dry flat; one vertical line means line dry. These are natural drying methods, not dryer settings.
Ironing: dots in the iron specify increasing permitted heat levels: one low, two moderate, three high. Check the limits for the label’s system and any steam restriction. A crossed-out iron means do not iron. Do not infer that steam blocking is safe from the fiber name or a washing instruction.
Professional cleaning: the circle is for professional textile care. P and F identify different permitted solvent groups for dry cleaning; the cleaner interprets the full symbol under the applicable standard. W means professional wet cleaning, not home washing. A bar underneath requires a gentler process. Give the cleaner the full label.
Use the specific yarn’s care instructions for washing, drying, and finishing your swatch and project. Machine washable does not also mean tumble-dryable or ironable.
Dye lot and color number
This is where people get caught. Two different numbers, two different purposes, and confusing them can mean a visible stripe across your sweater where you switched skeins mid-project.
The color number or name identifies a shade within a particular yarn line, for example an invented “Color 412” or “Dusty Rose.” The dye lot identifies a production batch, not the color itself. Different lots can differ visibly, but do not always do so.
Buy enough of the same lot when possible and compare the skeins. A matching lot is not a guarantee of perfectly uniform color, especially with hand-dyed yarn. If you must mix lots, try alternating skeins on a swatch first; it may soften a transition but cannot guarantee an invisible join.
The wording no dye lot means the manufacturer aims for consistent color across batches, without requiring a dye-lot match. It is not a promise that any two skeins will look identical; check the manufacturer’s explanation and compare them.
Country of origin and brand information
Brand, yarn line, product code, and any stated country of origin help identify the yarn. Their presence and format vary.
What the label doesn’t tell you
Labels cover a lot. But they leave out some things that matter.
A band alone cannot reliably predict the appearance or durability of your particular knitted fabric. Look for any manufacturer information, then use your own swatch to check the fabric and its response to the permitted care process.
And the gauge box is the manufacturer’s result, not yours. Treat it as a reference, not a guarantee.
Keep the label or a clear photo with your project notes, including the yarn name, length, fiber content, color, and dye lot.
FAQ
What if the label is in a language I can’t read? Identify the symbol system and ask the manufacturer about unfamiliar wording or marks. A symbol alone does not translate the fiber names or explain every care condition.
The label says 10 cm gauge but my pattern uses 4 inches. Same thing? Close, not identical. 10 cm is about 3.94 inches. If the pattern gives gauge over 10 cm, measure 10 cm. If it gives gauge over 4 inches, measure 4 inches.
Should I keep the yarn label? Yes. At least until the project is finished and washed.
What does “machine washable” mean for knitted items? Use the machine-washing process and temperature limits specified for that yarn. Check drying and ironing separately, and test the permitted care process on your swatch.